HobbyNox Rød 150ml Spray Lexan Lakk

Art.nr: HN1302

95,-

Du vil motta en e-post så snart produktet er på lager!

En ukjent feil har oppstått. Prøve igjen

MiniCars

1 På lager

Informasjon
Produsent

HobbyNox Rød 150ml Spray Lexan Lakk

Hobbynox™ R/C Racing maling er spesielt utviklet for maling/lakk av polykarbonatkbodyer. Det spesielle løsemiddelet som brukes i den etser overflaten, slik at malingen binder seg permanent til karosseriet.

Hobbynox™ rødlakk tips: Hvis det er mulig når du vil at rødt skal være hovedfargen med tilsatt lysere farger, må du maskere karosseriet slik at du maler det røde til slutt. Normalt trengs to til tre tynne lag med rødt for å dekke helt. Hvit anbefales på det sterkeste å bruke som bakgrunnsfarge da den får den røde til å se mer lys ut.

Funksjoner:

Drivstoffbestandig mot de fleste R/C bildrivstoff
Stor sprayboks - 150 ml
Ekstrem vedheft og veldig fleksibel
Tørker raskt
Spesiell spraydyse for jevne malingsstrøk

Hobbynox™ - Making you look Good!

Generic bodyshell painting tips from Pro-Line:

Cutting Your Bodyshell
Cut out the transparent bodyshell with a pair of scissors (this, this, this or this) or a sharp hobby knife with a new blade installed (this or this). Pay attention to keeping the corners smooth and with a radius. If you cut corners sharply the bodyshell will most likely start cracking at that place.

Body Mount Holes etc
Use a body reamer to make holes in the bodyshell - like this, this, this or this. The PROTOform Crosshair Body Mounting Kit #PF6032-00 can also be very helpful to location the body post holes if you forgot to do these holes prior to painting the bodyshell...

Sand the Edges Smooth
Smooth out any rough spots with this or this.

Don't remove the protective film
Leave the transparent protective film on the outside of the bodyshell on while painting.

Wash your Body
To remove any residue left on the body after molding, you must wash it inside and out. Use warm soapy (liquid dish washing detergent) water in your sink, paying special attention to the tight curved areas and corners. Rinse the body in warm water. Dry the body with a clean towel or hair dryer. It must be completely dry before you paint it.

Window Masks
If your bodyshell came equipped with pre-cut window masks: Using the molded in window lines as a guide apply the window masks to the inside the body. Be sure to press down all the edges to keep paint from sneaking under. The masks keep the windows clear while you paint.

Step 1: Tape Stripes
Make sure you use high quality masking tape, and press down all the edges. First mask off the color that you want to paint last. Masking tapes we recommend: 6 mm wide, 10 mm wide & 18 mm wide.

Step 2: Continue Taping
Fill in the area you want to paint with your second color. Painting from dark to light is ideal, so leave the darkest section clear, and paint this first.

Step 3: Mix the Paint
Shake the spray paint can you will use for at least a couple of minutes. There is a small steel ball inside that you will hear rattle inside. If you cant hear it - shake the can some more!

Step 4: First Coat
Apply a thin even first coat of paint from about 20-30 cm distance. Don't apply too much paint at this time as it will easily creep under the masking tape.

Step 5: Finish First Coat & remove mask
When your first color has completely dried, unmask the second section of the paint scheme. While removing the tape, watch that you don't remove any of the masking stripes accidentally.

Step 6: Paint 2nd color & remove mask
Again spray light coats and cover evenly. You can then back it with white or silver, but in this case we will use silver for the stripes, so no need to back it separately. When the paint has completely dried remove the taped stripes.

Step 7: Paint stripe
Now fill in the stripes with silver, and also back up the blue section in the middle, and on the bed.

Step 8: Window Trim
Painted window trim is very popular, and easy to create. When your final backup coat is dry, trace and trim around the inside of the window mask creating a border with a sharp hobby knife (this or this). Remove the borders from all the windows and spray with your favorite color.

Step 9: Trim & test fit
If you chose to not trim and mount the bodyshell prior to painting it then its time to do so! Trim out your body using curved scissors for the wheel wells and straight scissors for the lower lines. Drill out your body post markings with either a Dremel tool or reamer. The protective film will help keep your body from getting scratched as you cut and drill.

Step 10: Remove protective film & window masks
Peel back the protective film, and remove the window masks.

Step 11: Decal & Detail
Apply the decals included with the body, add extra details with a paint pen or a detail marker if you wish.

Done.

Lexan® is a registered trademark of General Electric Company.

Kommentarer

Share |

MiniCars

MiniCars er leverandør av rc produkter til forhandlere i hele skandinavia.

Minicars startades av Per Gustafsson redan 1968 i Ludvika. Verksamheten flyttade 1971 till Uppsala där den befann sig ända fram till 2009 då behovet av nya och större lokaler blev för stor. Lösningen blev att bygga ett nytt hus och idag huserar vi stolt i Enköping, strategiskt placerade intill E18 mellan Stockholm och Oslo.

Vi är sedan början av 80-talet en renodlad grossist (vi säljer endast till återförsäljare) som genom åren har lagt fler och fler fabrikat under våra fötter. Ett par milstolpar är t ex amerikanska Traxxas som vi började importera 1989 samt japanska Futaba som vi blev agenter för 1990. Idag är vi en av Europas största distributörer med över 100 olika fabrikat och varumärken och mer än 30 000 artiklar i sortimentet.

Minicars har idag 12 anställda och levererar varor till handlare i mer än 25 länder med de skandinaviska länderna som huvudmarknad.

ADRESS / KONTAKTMinicars Hobby Distribution AB

Annelundsgatan 17C
749 40 Enköping

Orgnummer: 556511-4302

Telefon: 0171-14 30 00

Info@minicars.se